Electrician recruiting: the first 90 days and early quits

A journeyman electrician in work boots and a hard hat shows a newer hire the inside of an open residential electrical panel in a garage, both holding flashlights, with a service van parked in the driv

New electricians quit early for a few predictable reasons: the job wasn’t what they were told, nobody showed them how they’d get paid or promoted, or they were left alone with a van and a schedule before they were ready. You can prevent most of that with a clear first 90 days and honest hiring up front.

Start fixing early quits before day one

Retention problems often begin in the screen. A licensed electrician who spent years on commercial new construction may not want to run residential service calls, talk to homeowners, and quote repairs on the spot. A great service tech may be bored on a tract-home rough-in crew. The license doesn’t tell you which one you’re hiring.

Ask every candidate what they’ve actually been doing: residential or commercial, new work or service, whether they’ve quoted jobs, and whether they’ve worked a full day of service calls on their own. Also confirm license level and state, and check the driving record for any role with a company vehicle. Licensing and apprentice rules vary by state, so verify what your state requires before you make an offer.

If you screen for the real job, the person who shows up on Monday already knows what Monday looks like. That’s the cheapest retention tool you have. We cover how this works across the trade on our electrical recruiting page.

Confirm the start and set up the first day

Some new hires never show up, and that’s a no-show, not a quit. Between offer and start, stay in touch. Send the start time, address, who they’re meeting, what to wear, and what to bring. Tell them whether tools, a phone, and a vehicle are provided.

On day one, have these ready:

Pay confusion causes more early resentment than low pay does. Walk through a sample paycheck so there are no surprises.

Week one: pair, don’t dump

Put every new hire with a strong senior electrician for the first week or two, even experienced journeymen. You’re teaching how your company works: how you quote, how you document, how you talk to customers, how you handle permits and inspections. A veteran from another shop still needs to learn your way.

Pick the mentor carefully. A senior tech who complains about the company will pass that on in a week. Give mentors a small bonus or a clear recognition for a successful ramp-up, so the job doesn’t feel like a favor.

Days 7 to 30: add responsibility in steps

Service electricians should move through stages: ride along, run calls with the mentor on the phone, then run calls solo with check-ins. Don’t send someone solo on a hard troubleshooting job because the schedule is full. A bad first solo call hurts the customer and the tech’s confidence.

For installers of EV chargers, generators, and panel upgrades, document the standard install: your preferred equipment, load calculation process, permit workflow, and photo requirements. Specialty work is in demand, and many shops are hiring for it. If your installers feel supported and trained, they have less reason to take a call from a competitor.

Hold a short check-in at the end of week one and again at day 30. Ask three things: what’s different from what you expected, what’s slowing you down, and what would make you consider leaving. Most people will tell you if you ask directly and don’t get defensive.

Apprentices: show the path in writing

Apprentices tend to choose the shop that offers hours toward a license and a clear raise schedule. Keep them by delivering on that from the start. Show them how hours are tracked, who signs off, what the raise steps are, and how classroom requirements fit with work schedules. Apprentice registration, supervision, and hour requirements differ by state, so confirm yours with the licensing board.

The common failure is apprentices spending months pulling wire and cleaning up with no exposure to other work. Rotate them through different jobs and tell them when the next step is coming. If you can’t offer variety, say so honestly in the ad and the interview.

Days 30 to 90: fix what the check-ins reveal

By day 30, you’ll know who is struggling and why. Common causes are poor dispatch, a mismatched mentor, unclear pay, or unreasonable schedules. Fix those quickly. Review each new hire’s calls or jobs with them at day 45 and day 60: what went well, what needs work, what’s next.

At day 90, have a real conversation about their pay, role, and path. Don’t wait for them to ask. Someone who hears “here’s what you’re doing well and here’s your next raise or responsibility” is less likely to answer a recruiter’s text.

Track the first 90 days like a pipeline

Keep a simple record: who started, who left, when, and why. After a few hires, you’ll see a pattern. Maybe commercial-background hires leave service roles by week three, or people quit when dispatch overloads them in the first month. You can’t fix what you don’t track.

If your problem is getting enough qualified candidates to inter

Stop chasing applicants. Start interviewing the right ones.

Book a demo and we will map your roles, your markets, and the plan that fits. Most campaigns launch within 48 hours.

Book a demo

Book a demo